ChangeLog 3.36 KB
Newer Older
Pavel Semerad's avatar
Pavel Semerad committed
1
*0.5.0 ()
2
    global menu was restructuralized
3
4
    added ability to select number of channels (2-MAX_CHANNELS) for each
	model, less channels means less delay
5
    poweron warn when not-centered now has separate global option
6
    added up/down timers with throttle trigger start
7
    added BRK button function to override throttle and apply full brake
8

Pavel Semerad's avatar
Pavel Semerad committed
9
*0.4.2 (13 Apr 2012)
10
    added global setting to disable center/reset value beep
Pavel Semerad's avatar
Pavel Semerad committed
11
    minimum battery voltage set to 2V for those experimenting with 1S cell
12
13
14
15
    PPM signal now uses constant length of SYNC signal to get it to
	receiver as soon as possible, also servo values are calculated
	just before generating servo PPM signals to have lowest
	steering/throttle to PPM signal delay
16
17
    ADC measuring every 1ms, averaging last 4 samples when used,
	globally settable to use last 4/1 values
18
    added poweron beep, can be set ON/OFF in global config
19
20
    at poweron, if steering or throttle are not in center dead zone,
	beep 3 times if poweron beep is allowed
21
22
    inactivity timer compares ADC values with previous ones, so now
	it will activate when radio is not center callibrated also
23
24
    added key function BLS to shutup battery low beeper, by default is
	assigned to END-long
25
    3-pos switch instead of CH3 button now works
26

Pavel Semerad's avatar
Pavel Semerad committed
27
*0.4.1 (17 Aug 2011)
Pavel Semerad's avatar
Pavel Semerad committed
28
29

    minimum battery voltage set to 6V
Pavel Semerad's avatar
Pavel Semerad committed
30
    CH3 key set default to OFF
31
    added DGR key function to reset DIG mix to centre
Pavel Semerad's avatar
Pavel Semerad committed
32
    added posibility to select DIG instead of channel number at MultiPosition
Pavel Semerad's avatar
Pavel Semerad committed
33
    added lap count functions assignable to keys
Pavel Semerad's avatar
Pavel Semerad committed
34

35
*0.4.0 (18 Jul 2011)
36
37
38
39

    use steering trim when dual-ESC steering
    added channel_speed for all channels, throttle channel can be applied only
	for forward side
40
41
42
    repaired setting to default values for functions of config-values mapped
	to trims, this should be done only for non-config values (channel,
	mix)
43

Pavel Semerad's avatar
Pavel Semerad committed
44
*0.3.2 (27 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
45

46
47
    added option throttle brake cut of to be able to drive forward only
	vehicles (boats)
Pavel Semerad's avatar
Pavel Semerad committed
48
    added MultiPosition settable to channel
49

Pavel Semerad's avatar
Pavel Semerad committed
50
*0.3.1 (26 Jun 2011)
51
52
53

    DIG mix can be set to channel 1 to have dual-ESC steering (boat, tank, ...)

Pavel Semerad's avatar
Pavel Semerad committed
54
*0.3.0 (24 Jun 2011)
55
56

    added globally settable key long-press delay
57
    when using trims, longer beep at value reset and short pause ignoring keys
58
59
60
    momentary trims/keys now sets value only when state of buttons changed
	(previously it always forced value to reflect button state), so it is
	possible to map momentary and non-momentary keys to the same
61
	channel/mix value, also value is showed when changed
62
63
64
    added possibility for momentary trims and 2-state keys to return not
	to centre/left, but to previous value which was active before button
	press
65

66
67
68
69
70
*0.2.0 (9 Jun 2011)

    added 4WS mix
    added DIG mix
    added steering speed (Turn, Return)
Pavel Semerad's avatar
Pavel Semerad committed
71
    added inactivity alarm
72
    added function C3R for keys to reset channel3 value to centre
Pavel Semerad's avatar
Pavel Semerad committed
73
    internal changes of trims momentary/opposite_reset
Pavel Semerad's avatar
Pavel Semerad committed
74

75
*0.1.0 (2 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
76
77
78

    added special chars "-1" and "10" to be able to display values -199...1099
    both trims-long now only resets, before there was 1 press of first button
79
    changed EEPROM init to eliminate broken initialization
80
    in menu: use ENTER to switch items and END/ENTER-long to end of edit of item
81
82
    added key mapping to configuration of model and removed coresponding
      global settings (trim_step, autorepeat, ch3_momentary)
Pavel Semerad's avatar
Pavel Semerad committed
83
84
85
86
87
88


*0.0.0 (25 May 2011)

    initial public revision