ChangeLog 3.87 KB
Newer Older
1
2
3
*0.6.0 ()
    increased model memories by using FLASH also

Pavel Semerad's avatar
Pavel Semerad committed
4
*0.5.1 (26 Apr 2012)
5
6
    added possibility to connect potentiometer instead of CH3 button

Pavel Semerad's avatar
Pavel Semerad committed
7
*0.5.0 (23 Apr 2012)
8
    global menu was restructuralized
9
10
    added ability to select number of channels (2-MAX_CHANNELS) for each
	model, less channels means less delay
11
    poweron warn when not-centered now has separate global option
12
    added up/down/lap timers with throttle trigger start
13
    added BRK button function to override throttle and apply full brake
14
15
    big internal changes handling different menus, key mapping uses
	2-char option identification instead of various symbols
16
17
    added global option rotate_reverse to switch direction of rotate
	endoder at GT3C
18
19
    added globally settable PPM constant sync/constant frame + selection
	of length
20
    added new menu to directly set channel 3-8 value
21

Pavel Semerad's avatar
Pavel Semerad committed
22
*0.4.2 (13 Apr 2012)
23
    added global setting to disable center/reset value beep
Pavel Semerad's avatar
Pavel Semerad committed
24
    minimum battery voltage set to 2V for those experimenting with 1S cell
25
26
27
28
    PPM signal now uses constant length of SYNC signal to get it to
	receiver as soon as possible, also servo values are calculated
	just before generating servo PPM signals to have lowest
	steering/throttle to PPM signal delay
29
30
    ADC measuring every 1ms, averaging last 4 samples when used,
	globally settable to use last 4/1 values
31
    added poweron beep, can be set ON/OFF in global config
32
33
    at poweron, if steering or throttle are not in center dead zone,
	beep 3 times if poweron beep is allowed
34
35
    inactivity timer compares ADC values with previous ones, so now
	it will activate when radio is not center callibrated also
36
37
    added key function BLS to shutup battery low beeper, by default is
	assigned to END-long
38
    3-pos switch instead of CH3 button now works
39

Pavel Semerad's avatar
Pavel Semerad committed
40
*0.4.1 (17 Aug 2011)
Pavel Semerad's avatar
Pavel Semerad committed
41
42

    minimum battery voltage set to 6V
Pavel Semerad's avatar
Pavel Semerad committed
43
    CH3 key set default to OFF
44
    added DGR key function to reset DIG mix to centre
Pavel Semerad's avatar
Pavel Semerad committed
45
    added posibility to select DIG instead of channel number at MultiPosition
Pavel Semerad's avatar
Pavel Semerad committed
46
    added lap count functions assignable to keys
Pavel Semerad's avatar
Pavel Semerad committed
47

48
*0.4.0 (18 Jul 2011)
49
50
51
52

    use steering trim when dual-ESC steering
    added channel_speed for all channels, throttle channel can be applied only
	for forward side
53
54
55
    repaired setting to default values for functions of config-values mapped
	to trims, this should be done only for non-config values (channel,
	mix)
56

Pavel Semerad's avatar
Pavel Semerad committed
57
*0.3.2 (27 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
58

59
60
    added option throttle brake cut of to be able to drive forward only
	vehicles (boats)
Pavel Semerad's avatar
Pavel Semerad committed
61
    added MultiPosition settable to channel
62

Pavel Semerad's avatar
Pavel Semerad committed
63
*0.3.1 (26 Jun 2011)
64
65
66

    DIG mix can be set to channel 1 to have dual-ESC steering (boat, tank, ...)

Pavel Semerad's avatar
Pavel Semerad committed
67
*0.3.0 (24 Jun 2011)
68
69

    added globally settable key long-press delay
70
    when using trims, longer beep at value reset and short pause ignoring keys
71
72
73
    momentary trims/keys now sets value only when state of buttons changed
	(previously it always forced value to reflect button state), so it is
	possible to map momentary and non-momentary keys to the same
74
	channel/mix value, also value is showed when changed
75
76
77
    added possibility for momentary trims and 2-state keys to return not
	to centre/left, but to previous value which was active before button
	press
78

79
80
81
82
83
*0.2.0 (9 Jun 2011)

    added 4WS mix
    added DIG mix
    added steering speed (Turn, Return)
Pavel Semerad's avatar
Pavel Semerad committed
84
    added inactivity alarm
85
    added function C3R for keys to reset channel3 value to centre
Pavel Semerad's avatar
Pavel Semerad committed
86
    internal changes of trims momentary/opposite_reset
Pavel Semerad's avatar
Pavel Semerad committed
87

88
*0.1.0 (2 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
89
90
91

    added special chars "-1" and "10" to be able to display values -199...1099
    both trims-long now only resets, before there was 1 press of first button
92
    changed EEPROM init to eliminate broken initialization
93
    in menu: use ENTER to switch items and END/ENTER-long to end of edit of item
94
95
    added key mapping to configuration of model and removed coresponding
      global settings (trim_step, autorepeat, ch3_momentary)
Pavel Semerad's avatar
Pavel Semerad committed
96
97
98
99
100
101


*0.0.0 (25 May 2011)

    initial public revision