ChangeLog 4.27 KB
Newer Older
Pavel Semerad's avatar
Pavel Semerad committed
1
2
*0.6.2 ()

Pavel Semerad's avatar
Pavel Semerad committed
3
*0.6.1 (18 Jun 2012)
4
    repaired ABS to use cycle length same as before PPM frame length changes
5
    added extra brake channel for throttle brake side
6
7
    repaired steering/throttle/channel speed to not beeing dependent
	on ppm frame length
8
    added buttons LOCK until ENTER-long to global menu
9
    repaired key setting, buttons long RS and EN were unaccesible
Pavel Semerad's avatar
Pavel Semerad committed
10

Pavel Semerad's avatar
Pavel Semerad committed
11
*0.6.0 (28 Apr 2012)
12
    increased model memories by using FLASH also
13
    added more Multi-Positions
14

Pavel Semerad's avatar
Pavel Semerad committed
15
*0.5.1 (26 Apr 2012)
16
17
    added possibility to connect potentiometer instead of CH3 button

Pavel Semerad's avatar
Pavel Semerad committed
18
*0.5.0 (23 Apr 2012)
19
    global menu was restructuralized
20
21
    added ability to select number of channels (2-MAX_CHANNELS) for each
	model, less channels means less delay
22
    poweron warn when not-centered now has separate global option
23
    added up/down/lap timers with throttle trigger start
24
    added BRK button function to override throttle and apply full brake
25
26
    big internal changes handling different menus, key mapping uses
	2-char option identification instead of various symbols
27
28
    added global option rotate_reverse to switch direction of rotate
	endoder at GT3C
29
30
    added globally settable PPM constant sync/constant frame + selection
	of length
31
    added new menu to directly set channel 3-8 value
32

Pavel Semerad's avatar
Pavel Semerad committed
33
*0.4.2 (13 Apr 2012)
34
    added global setting to disable center/reset value beep
Pavel Semerad's avatar
Pavel Semerad committed
35
    minimum battery voltage set to 2V for those experimenting with 1S cell
36
37
38
39
    PPM signal now uses constant length of SYNC signal to get it to
	receiver as soon as possible, also servo values are calculated
	just before generating servo PPM signals to have lowest
	steering/throttle to PPM signal delay
40
41
    ADC measuring every 1ms, averaging last 4 samples when used,
	globally settable to use last 4/1 values
42
    added poweron beep, can be set ON/OFF in global config
43
44
    at poweron, if steering or throttle are not in center dead zone,
	beep 3 times if poweron beep is allowed
45
46
    inactivity timer compares ADC values with previous ones, so now
	it will activate when radio is not center callibrated also
47
48
    added key function BLS to shutup battery low beeper, by default is
	assigned to END-long
49
    3-pos switch instead of CH3 button now works
50

Pavel Semerad's avatar
Pavel Semerad committed
51
*0.4.1 (17 Aug 2011)
Pavel Semerad's avatar
Pavel Semerad committed
52
53

    minimum battery voltage set to 6V
Pavel Semerad's avatar
Pavel Semerad committed
54
    CH3 key set default to OFF
55
    added DGR key function to reset DIG mix to centre
Pavel Semerad's avatar
Pavel Semerad committed
56
    added posibility to select DIG instead of channel number at MultiPosition
Pavel Semerad's avatar
Pavel Semerad committed
57
    added lap count functions assignable to keys
Pavel Semerad's avatar
Pavel Semerad committed
58

59
*0.4.0 (18 Jul 2011)
60
61
62
63

    use steering trim when dual-ESC steering
    added channel_speed for all channels, throttle channel can be applied only
	for forward side
64
65
66
    repaired setting to default values for functions of config-values mapped
	to trims, this should be done only for non-config values (channel,
	mix)
67

Pavel Semerad's avatar
Pavel Semerad committed
68
*0.3.2 (27 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
69

70
71
    added option throttle brake cut of to be able to drive forward only
	vehicles (boats)
Pavel Semerad's avatar
Pavel Semerad committed
72
    added MultiPosition settable to channel
73

Pavel Semerad's avatar
Pavel Semerad committed
74
*0.3.1 (26 Jun 2011)
75
76
77

    DIG mix can be set to channel 1 to have dual-ESC steering (boat, tank, ...)

Pavel Semerad's avatar
Pavel Semerad committed
78
*0.3.0 (24 Jun 2011)
79
80

    added globally settable key long-press delay
81
    when using trims, longer beep at value reset and short pause ignoring keys
82
83
84
    momentary trims/keys now sets value only when state of buttons changed
	(previously it always forced value to reflect button state), so it is
	possible to map momentary and non-momentary keys to the same
85
	channel/mix value, also value is showed when changed
86
87
88
    added possibility for momentary trims and 2-state keys to return not
	to centre/left, but to previous value which was active before button
	press
89

90
91
92
93
94
*0.2.0 (9 Jun 2011)

    added 4WS mix
    added DIG mix
    added steering speed (Turn, Return)
Pavel Semerad's avatar
Pavel Semerad committed
95
    added inactivity alarm
96
    added function C3R for keys to reset channel3 value to centre
Pavel Semerad's avatar
Pavel Semerad committed
97
    internal changes of trims momentary/opposite_reset
Pavel Semerad's avatar
Pavel Semerad committed
98

99
*0.1.0 (2 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
100
101
102

    added special chars "-1" and "10" to be able to display values -199...1099
    both trims-long now only resets, before there was 1 press of first button
103
    changed EEPROM init to eliminate broken initialization
104
    in menu: use ENTER to switch items and END/ENTER-long to end of edit of item
105
106
    added key mapping to configuration of model and removed coresponding
      global settings (trim_step, autorepeat, ch3_momentary)
Pavel Semerad's avatar
Pavel Semerad committed
107
108
109
110
111
112


*0.0.0 (25 May 2011)

    initial public revision