ChangeLog 2.56 KB
Newer Older
1
2
*0.4.2 ()
    added global setting to disable center/reset value beep
Pavel Semerad's avatar
Pavel Semerad committed
3
    minimum battery voltage set to 2V for those experimenting with 1S cell
4
    PPM length shortened to "NUM_CHANNELS x 2ms + 5ms" to send new data
5
	to receiver as soon as possible
6
    ADC measuring every 1ms, averaging last 4 samples when used
7
8
9
    after poweron, if steering or throttle are not in center dead zone,
	show calibration screen, because recalibration will be probably
	needed
10

Pavel Semerad's avatar
Pavel Semerad committed
11
*0.4.1 (17 Aug 2011)
Pavel Semerad's avatar
Pavel Semerad committed
12
13

    minimum battery voltage set to 6V
Pavel Semerad's avatar
Pavel Semerad committed
14
    CH3 key set default to OFF
15
    added DGR key function to reset DIG mix to centre
Pavel Semerad's avatar
Pavel Semerad committed
16
    added posibility to select DIG instead of channel number at MultiPosition
Pavel Semerad's avatar
Pavel Semerad committed
17
    added lap count functions assignable to keys
Pavel Semerad's avatar
Pavel Semerad committed
18

19
*0.4.0 (18 Jul 2011)
20
21
22
23

    use steering trim when dual-ESC steering
    added channel_speed for all channels, throttle channel can be applied only
	for forward side
24
25
26
    repaired setting to default values for functions of config-values mapped
	to trims, this should be done only for non-config values (channel,
	mix)
27

Pavel Semerad's avatar
Pavel Semerad committed
28
*0.3.2 (27 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
29

30
31
    added option throttle brake cut of to be able to drive forward only
	vehicles (boats)
Pavel Semerad's avatar
Pavel Semerad committed
32
    added MultiPosition settable to channel
33

Pavel Semerad's avatar
Pavel Semerad committed
34
*0.3.1 (26 Jun 2011)
35
36
37

    DIG mix can be set to channel 1 to have dual-ESC steering (boat, tank, ...)

Pavel Semerad's avatar
Pavel Semerad committed
38
*0.3.0 (24 Jun 2011)
39
40

    added globally settable key long-press delay
41
    when using trims, longer beep at value reset and short pause ignoring keys
42
43
44
    momentary trims/keys now sets value only when state of buttons changed
	(previously it always forced value to reflect button state), so it is
	possible to map momentary and non-momentary keys to the same
45
	channel/mix value, also value is showed when changed
46
47
48
    added possibility for momentary trims and 2-state keys to return not
	to centre/left, but to previous value which was active before button
	press
49

50
51
52
53
54
*0.2.0 (9 Jun 2011)

    added 4WS mix
    added DIG mix
    added steering speed (Turn, Return)
Pavel Semerad's avatar
Pavel Semerad committed
55
    added inactivity alarm
56
    added function C3R for keys to reset channel3 value to centre
Pavel Semerad's avatar
Pavel Semerad committed
57
    internal changes of trims momentary/opposite_reset
Pavel Semerad's avatar
Pavel Semerad committed
58

59
*0.1.0 (2 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
60
61
62

    added special chars "-1" and "10" to be able to display values -199...1099
    both trims-long now only resets, before there was 1 press of first button
63
    changed EEPROM init to eliminate broken initialization
64
    in menu: use ENTER to switch items and END/ENTER-long to end of edit of item
65
66
    added key mapping to configuration of model and removed coresponding
      global settings (trim_step, autorepeat, ch3_momentary)
Pavel Semerad's avatar
Pavel Semerad committed
67
68
69
70
71
72


*0.0.0 (25 May 2011)

    initial public revision