ChangeLog 3.72 KB
Newer Older
Pavel Semerad's avatar
Pavel Semerad committed
1
*0.5.0 (23 Apr 2012)
2
    global menu was restructuralized
3
4
    added ability to select number of channels (2-MAX_CHANNELS) for each
	model, less channels means less delay
5
    poweron warn when not-centered now has separate global option
6
    added up/down/lap timers with throttle trigger start
7
    added BRK button function to override throttle and apply full brake
8
9
    big internal changes handling different menus, key mapping uses
	2-char option identification instead of various symbols
10
11
    added global option rotate_reverse to switch direction of rotate
	endoder at GT3C
12
13
    added globally settable PPM constant sync/constant frame + selection
	of length
14
    added new menu to directly set channel 3-8 value
15

Pavel Semerad's avatar
Pavel Semerad committed
16
*0.4.2 (13 Apr 2012)
17
    added global setting to disable center/reset value beep
Pavel Semerad's avatar
Pavel Semerad committed
18
    minimum battery voltage set to 2V for those experimenting with 1S cell
19
20
21
22
    PPM signal now uses constant length of SYNC signal to get it to
	receiver as soon as possible, also servo values are calculated
	just before generating servo PPM signals to have lowest
	steering/throttle to PPM signal delay
23
24
    ADC measuring every 1ms, averaging last 4 samples when used,
	globally settable to use last 4/1 values
25
    added poweron beep, can be set ON/OFF in global config
26
27
    at poweron, if steering or throttle are not in center dead zone,
	beep 3 times if poweron beep is allowed
28
29
    inactivity timer compares ADC values with previous ones, so now
	it will activate when radio is not center callibrated also
30
31
    added key function BLS to shutup battery low beeper, by default is
	assigned to END-long
32
    3-pos switch instead of CH3 button now works
33

Pavel Semerad's avatar
Pavel Semerad committed
34
*0.4.1 (17 Aug 2011)
Pavel Semerad's avatar
Pavel Semerad committed
35
36

    minimum battery voltage set to 6V
Pavel Semerad's avatar
Pavel Semerad committed
37
    CH3 key set default to OFF
38
    added DGR key function to reset DIG mix to centre
Pavel Semerad's avatar
Pavel Semerad committed
39
    added posibility to select DIG instead of channel number at MultiPosition
Pavel Semerad's avatar
Pavel Semerad committed
40
    added lap count functions assignable to keys
Pavel Semerad's avatar
Pavel Semerad committed
41

42
*0.4.0 (18 Jul 2011)
43
44
45
46

    use steering trim when dual-ESC steering
    added channel_speed for all channels, throttle channel can be applied only
	for forward side
47
48
49
    repaired setting to default values for functions of config-values mapped
	to trims, this should be done only for non-config values (channel,
	mix)
50

Pavel Semerad's avatar
Pavel Semerad committed
51
*0.3.2 (27 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
52

53
54
    added option throttle brake cut of to be able to drive forward only
	vehicles (boats)
Pavel Semerad's avatar
Pavel Semerad committed
55
    added MultiPosition settable to channel
56

Pavel Semerad's avatar
Pavel Semerad committed
57
*0.3.1 (26 Jun 2011)
58
59
60

    DIG mix can be set to channel 1 to have dual-ESC steering (boat, tank, ...)

Pavel Semerad's avatar
Pavel Semerad committed
61
*0.3.0 (24 Jun 2011)
62
63

    added globally settable key long-press delay
64
    when using trims, longer beep at value reset and short pause ignoring keys
65
66
67
    momentary trims/keys now sets value only when state of buttons changed
	(previously it always forced value to reflect button state), so it is
	possible to map momentary and non-momentary keys to the same
68
	channel/mix value, also value is showed when changed
69
70
71
    added possibility for momentary trims and 2-state keys to return not
	to centre/left, but to previous value which was active before button
	press
72

73
74
75
76
77
*0.2.0 (9 Jun 2011)

    added 4WS mix
    added DIG mix
    added steering speed (Turn, Return)
Pavel Semerad's avatar
Pavel Semerad committed
78
    added inactivity alarm
79
    added function C3R for keys to reset channel3 value to centre
Pavel Semerad's avatar
Pavel Semerad committed
80
    internal changes of trims momentary/opposite_reset
Pavel Semerad's avatar
Pavel Semerad committed
81

82
*0.1.0 (2 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
83
84
85

    added special chars "-1" and "10" to be able to display values -199...1099
    both trims-long now only resets, before there was 1 press of first button
86
    changed EEPROM init to eliminate broken initialization
87
    in menu: use ENTER to switch items and END/ENTER-long to end of edit of item
88
89
    added key mapping to configuration of model and removed coresponding
      global settings (trim_step, autorepeat, ch3_momentary)
Pavel Semerad's avatar
Pavel Semerad committed
90
91
92
93
94
95


*0.0.0 (25 May 2011)

    initial public revision