ChangeLog 4.13 KB
Newer Older
Pavel Semerad's avatar
Pavel Semerad committed
1
*0.6.1 ()
2
    repaired ABS to use cycle length same as before PPM frame length changes
3
    added extra brake channel for throttle brake side
4
5
    repaired steering/throttle/channel speed to not beeing dependent
	on ppm frame length
Pavel Semerad's avatar
Pavel Semerad committed
6

Pavel Semerad's avatar
Pavel Semerad committed
7
*0.6.0 (28 Apr 2012)
8
    increased model memories by using FLASH also
9
    added more Multi-Positions
10

Pavel Semerad's avatar
Pavel Semerad committed
11
*0.5.1 (26 Apr 2012)
12
13
    added possibility to connect potentiometer instead of CH3 button

Pavel Semerad's avatar
Pavel Semerad committed
14
*0.5.0 (23 Apr 2012)
15
    global menu was restructuralized
16
17
    added ability to select number of channels (2-MAX_CHANNELS) for each
	model, less channels means less delay
18
    poweron warn when not-centered now has separate global option
19
    added up/down/lap timers with throttle trigger start
20
    added BRK button function to override throttle and apply full brake
21
22
    big internal changes handling different menus, key mapping uses
	2-char option identification instead of various symbols
23
24
    added global option rotate_reverse to switch direction of rotate
	endoder at GT3C
25
26
    added globally settable PPM constant sync/constant frame + selection
	of length
27
    added new menu to directly set channel 3-8 value
28

Pavel Semerad's avatar
Pavel Semerad committed
29
*0.4.2 (13 Apr 2012)
30
    added global setting to disable center/reset value beep
Pavel Semerad's avatar
Pavel Semerad committed
31
    minimum battery voltage set to 2V for those experimenting with 1S cell
32
33
34
35
    PPM signal now uses constant length of SYNC signal to get it to
	receiver as soon as possible, also servo values are calculated
	just before generating servo PPM signals to have lowest
	steering/throttle to PPM signal delay
36
37
    ADC measuring every 1ms, averaging last 4 samples when used,
	globally settable to use last 4/1 values
38
    added poweron beep, can be set ON/OFF in global config
39
40
    at poweron, if steering or throttle are not in center dead zone,
	beep 3 times if poweron beep is allowed
41
42
    inactivity timer compares ADC values with previous ones, so now
	it will activate when radio is not center callibrated also
43
44
    added key function BLS to shutup battery low beeper, by default is
	assigned to END-long
45
    3-pos switch instead of CH3 button now works
46

Pavel Semerad's avatar
Pavel Semerad committed
47
*0.4.1 (17 Aug 2011)
Pavel Semerad's avatar
Pavel Semerad committed
48
49

    minimum battery voltage set to 6V
Pavel Semerad's avatar
Pavel Semerad committed
50
    CH3 key set default to OFF
51
    added DGR key function to reset DIG mix to centre
Pavel Semerad's avatar
Pavel Semerad committed
52
    added posibility to select DIG instead of channel number at MultiPosition
Pavel Semerad's avatar
Pavel Semerad committed
53
    added lap count functions assignable to keys
Pavel Semerad's avatar
Pavel Semerad committed
54

55
*0.4.0 (18 Jul 2011)
56
57
58
59

    use steering trim when dual-ESC steering
    added channel_speed for all channels, throttle channel can be applied only
	for forward side
60
61
62
    repaired setting to default values for functions of config-values mapped
	to trims, this should be done only for non-config values (channel,
	mix)
63

Pavel Semerad's avatar
Pavel Semerad committed
64
*0.3.2 (27 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
65

66
67
    added option throttle brake cut of to be able to drive forward only
	vehicles (boats)
Pavel Semerad's avatar
Pavel Semerad committed
68
    added MultiPosition settable to channel
69

Pavel Semerad's avatar
Pavel Semerad committed
70
*0.3.1 (26 Jun 2011)
71
72
73

    DIG mix can be set to channel 1 to have dual-ESC steering (boat, tank, ...)

Pavel Semerad's avatar
Pavel Semerad committed
74
*0.3.0 (24 Jun 2011)
75
76

    added globally settable key long-press delay
77
    when using trims, longer beep at value reset and short pause ignoring keys
78
79
80
    momentary trims/keys now sets value only when state of buttons changed
	(previously it always forced value to reflect button state), so it is
	possible to map momentary and non-momentary keys to the same
81
	channel/mix value, also value is showed when changed
82
83
84
    added possibility for momentary trims and 2-state keys to return not
	to centre/left, but to previous value which was active before button
	press
85

86
87
88
89
90
*0.2.0 (9 Jun 2011)

    added 4WS mix
    added DIG mix
    added steering speed (Turn, Return)
Pavel Semerad's avatar
Pavel Semerad committed
91
    added inactivity alarm
92
    added function C3R for keys to reset channel3 value to centre
Pavel Semerad's avatar
Pavel Semerad committed
93
    internal changes of trims momentary/opposite_reset
Pavel Semerad's avatar
Pavel Semerad committed
94

95
*0.1.0 (2 Jun 2011)
Pavel Semerad's avatar
Pavel Semerad committed
96
97
98

    added special chars "-1" and "10" to be able to display values -199...1099
    both trims-long now only resets, before there was 1 press of first button
99
    changed EEPROM init to eliminate broken initialization
100
    in menu: use ENTER to switch items and END/ENTER-long to end of edit of item
101
102
    added key mapping to configuration of model and removed coresponding
      global settings (trim_step, autorepeat, ch3_momentary)
Pavel Semerad's avatar
Pavel Semerad committed
103
104
105
106
107
108


*0.0.0 (25 May 2011)

    initial public revision